Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
This article which follows pertaining to A Step-by-Step Guide to Installing a Bathtub is exceptionally attention-grabbing. Don't overlook it.
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately hard project. If the old tub is conveniently obtainable, the job can relocate rapidly; if you need to open a wall to remove the old tub and also place the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. Ensure you have actually qualified yourself for the job as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Chances are you might require an expert plumber to make tube links.
This article will certainly assist you set up a brand-new bath tub in your washroom if you have already bought a new bathtub as well as do not need to change the setup of your previous water supply pipelines.
Your tools as well as material list need to make up the following:
Planning for the Installation
To start with, the supporting frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bath tub in the required position. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub until the level reviews degree.
To install faucets, fit all-time low of the outermost adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the tub must wait till the tub has been used at least once as this will resolve it into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making sure that the washers are in location between the faucet and the sink. Safeguard the tap in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split an inflexible seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in issues with wetness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealant can crack rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our part about How to Install a Bathtub Yourself. Thank you for taking time to read our blog. Are you aware of another person who is fascinated by the subject? Please feel free to promote it. Thanks a lot for your time. Kindly pay a visit to our blog back soon.
Secure your space, call! Report this page